Stop Set. This refers to the slots for commercials during the broadcast hour. They may be recurring and of the same length. They may be filled by paid advertising spots or by public service announcements. Stop-set length can vary greatly between local stations and even network programming.
Furthermore, what is a ferrule and stop set?
Ferrule and Stop sets are used for looping and swaging the ends of wire rope. Designed for light duty applications. Proper assembly recommends setting with a swaging tool instead of a hammer.
Similarly, what is a sot in broadcast? Sound on tape, or SOT, is sound or video usually recorded in the field. It is usually an interview or soundbite. Radio was the first medium for broadcast journalism.
Similarly one may ask, how do you use cable stops?
Begin assembly with an end stop. Place the fitting between the jaws of the swaging tool and compress it firmly onto the wire rope. Swaging is the act of permanently attaching sleeves and fittings to wire rope. The swaging tool is a cold metal press that allows you to crimp ferrules and other attachments onto the cable.
When should you not use ferrules?
ferrules are great. wires between 1mm² and 2.5mm² : No ferrules. wires above 2.5mm² : Ferrules or lugs. Since 99% of our control wiring is 1mm, that means that we generally do not use ferrules with cage clamp terminals.
How does a ferrule work?
As the ferrule(s) moves axially into the fitting body, the body's angled shape radially compresses the end of the ferrule onto the outer diameter of the tubing. It is this radial compression that creates the leak tight seal between the fitting, ferrule, and tubing, and gives the compression fitting its name.How do you tighten ferrules?
The steel ferrules are designed to swage into place permanently. To do this, you need to tighten to finger tight, then put on another 1.25 turns with a wrench. However, if you do this, the ferrules will bite into and deform the tubing. One of the two ferrule pieces will be captive, so this is a permanent installation.How do you install a ferrule?
Turn the club upside down and tap it onto the ground to push the ferrule farther onto the shaft. Alternatively, press the shaft into a ferrule installing device, choose the correctly sized hole and then push the shaft all the way down into the device, which sets the ferrule into the proper position.How do you crimp a ferrule without tools?
2 Answers. Just crush the thing with any tool you have around. If you can use a big vise to crush them down, that's probably the most 'controlled' way. Otherwise, use pliers, or get a hammer and chisel and dent the sleeve at two or three points with the chisel.How does a swaging tool work?
How to Use a Swaging Tool- Slide the metal sleeve over the end and down the steel cable if you are making a loop.
- Pull the end of the steel cable up and over the running side of the steel cable and insert the end of the cable into the metal sleeve if you are making a loop.
- Open the jaws of the swaging tool by pulling the handles apart.
What is the difference between swaging and crimping?
The most important distinction is that, in crimping, the compression force is applied once (or at most a few times), while in swaging the force is applied many times at high frequency. In swaging, the product is usually moved slowly into a tapered die while the die closes and opens rapidly.How do you crimp a ferrule cable?
Place the ferrule over the bare metal strands of the wire. Around 0.5mm of bare strands should be left outside of the ferrule barrel. Insert the ferrule and wire into the closest-sized notch on the crimp tool. Squeeze the handles of the crimp tool together firmly to lock the ferrule onto the end of the wire.How do you terminate a wire rope?
Types of Wire Rope End Terminations There are essentially two techniques that can be used to create a termination on a length of wire rope or cable: You can form an eye, or loop, in the wire rope. You can attach a fitting to the end of the wire rope.What is a swage sleeve?
Swage sleeves (also known as wire rope clamps, cable ferrules & crimps) are fittings commonly used to form loop ends or wire splices. Swage sleeves are available in plain copper, zinc plated copper, tin plated copper, aluminum and stainless steel material.How do I write a VO SOT script?
Part 1: The VO Script- <ANC> Command begins story. ( SHIFT F8)
- "TAKE VO" Command comes after anchor lead-in. ( SHIFT F1)
- :20 second script under video is written to match available video.
- Last sentence before the SOT typically "sets-up" or introduces the person in the SOT. Ends with "TAKE SOT" (SHIFT F2)
