What does error code e10 mean?

It indicates problem with not taking in water, not taken in enough water or problems with the drain.

Also know, what is error code e10?

Seeing E10 or ten repeated flashes of the LED on your display panel between pauses means your machine has identified a specific problem. Error code E10 relates to a fault either with the timer (on older models) or with the drum sensor that ensures the drum is in the correct position.

Furthermore, what does e10 mean on Zanussi washing machine? Zanussi Washing Machine Error Code = E10 Error Code Definition = The washer does not fill with water properly.

Additionally, what does e10 mean on my AEG washing machine?

AEG failure E10, C1 or F1 When you see E10, C1 or F1 on the display, the washing machine doesn't get enough water.

What does EHO mean on a washing machine?

power supply

What does e10 mean on a boiler?

E10 Indicates no flow through the boiler on the venting cycle often associated with refilling or installing of the Remeha Avanta boiler. Check for minimum water pressure. Check that the pump is working and or has been correctly installed and wired.

What does e10 mean on Logik washing machine?

Water drain time out

How do you fix an e10 error on an Electrolux washing machine?

Resolution:

Check the water supply.
Clean the filter in the inlet hose next to the tap.
Ensure correct position of the drain hose.
Ensure correct drain height.
Clean the pump and filter.
Check for blocked drain.
Check the drainage hose for possible kink or twist.
Use less soap powder.

What does e mean on Electrolux washer?

Drain Pump Error -

What does e11 mean on a Simpson washing machine?

Rating is available when the video has been rented. Published on Nov 6, 2015. An E 11 error indicates a problem with the dryer sensor. This video shows how to replace this sensor and identify damage to the wirig that may cause this problem.

What does e20 mean on Electrolux washing machine?

Washing machine displays error message E20 or C2, emits 2 beeps or 2 flashes. It indicates pumping problems.

How do I reset my AEG washing machine?

Resetting guide: Press the two buttons at the top (soak and pre-wash). At the same time, turn the cycle selector counter-clockwise to the delicate spin cycle. Then release the two buttons and continue turning the selector counter-clockwise all the way round to off (almost one full turn).

What does a10 mean on a Hoover dryer?

all in one

What is an e20 error?

Washing machine displays error message E20, E21 or C2, emits 2 beeps or 2 flashes. It indicates pumping problems. Washing machine does not drain. The drum does not turn. The appliance makes an unusual noise because of the blockage of the drain pump.

How do you clean an AEG front loader?

Cleaning the detergent dispenser:

Remove any spillage or residue in each compartment by rinsing it under hot running tap water.
Remove the dispenser and use a suitable brush (Clean it with an old toothbrush) to remove any dirt and dried soap powder/liquid from each section.

How do you fix an EFO washing machine?

Resolution:

Use less detergent. Using too much detergent may cause excessive foaming.
Clean the dispenser drawer.
Check for laundry caught in the machine.
Check for leaking at the bottom – fluff filter.
Check the water supply hose.
Check the door seal.
Contact an Authorized Service Centre.

How do I reset my Electrolux dryer?

To reset your Electrolux dryer, press and hold the "temperature" and "dryness" buttons simultaneously. Keep these buttons depressed for at least six seconds to reset the machine. If this doesn't clear your error code, you likely need service.

What does e12 mean on a Grundig washing machine?

flood switch error code

How do you clear a Zanussi error code?

Step 1 Zanussi Washing Machine Fault Code Reset

Turn the dial to off.
Press and hold together the start button (the one with the green arrow) and the button to the left of it.
While holding, turn the Programme Dial 1 'click' clockwise(to 90 degrees temp).

How long is Zanussi guarantee?

1 year

How do clean a washing machine?

Add two cups of white cleaning vinegar to detergent dispenser. Run it through a complete cycle. Run another cycle on the highest level and at the hottest water temperature, this time adding one-half cup of baking soda to the drum. When cycle is done, wipe inside drum of washer with a damp microfiber cloth.