What does AF mean on Kenmore dryer?

AF means Air Flow issue. This particular dryer has two belts, one for drum and another one is for the blower wheel.

Similarly, what does the code AF mean on a Kenmore Dryer?

The code AF normally indicates that the control senses a restricted air flow on most models of Kenmore Elite dryers. Check the flexible vent connection behind your dryer. Make sure that it is not kinked or clogged.

Also Know, what does F mean on Kenmore Elite dryer? F-40. Communication error between the main electronic control board and the blower motor control board. Check/ Repair. Unplug the dryer and check the wire harness connections between the blower motor control board and the main electronic control board.

Besides, what does it mean when my dryer Says AF?

The letters "AF" flashes if a restricted air flow condition exists, meaning that 3 consecutive cycles were run with airflow less that 19CFM. Check the entire venting system for any kinks or restrictions. Check the door seal and drum seals.

How do you run a diagnostic on a Kenmore Elite dryer?

Hi ben, here is the process for entering the diagnostic mode, (use any button except STOP) press the button and hold for 3 seconds, release for three seconds, press and hold 3 seconds, release for 3 seconds, press and hold for 3 seconds , the mode has been entered.

What does AF mean on Whirlpool dryer?

AF or F4E3. Restricted air flow. It indicates that the lint screen or vent is clogged; the vent is crushed, kinked or has too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.

How do you clean the lint out of a Whirlpool Cabrio dryer?

To clean inside the dryer, unplug it and turn off the gas, then open either the top or the front. The procedure is the same for gas and electric dryers. For dryers with a top lint filter and a solid front panel, remove the lint filter and take out the two screws on the side of the lint filter opening.

What is AF on Maytag dryer?

An AF (Restricted Air Flow) error code indicates that the lint screen or house vent is clogged; the vent may be crushed, kinked or have too many turns. The dryer will continue to run when the is error is present. Touch any key to clear the code from the display and return to the estimated time remaining.

What does PF mean on a Whirlpool Cabrio dryer?

power failure

How do I reset my Whirlpool Cabrio dryer?

How to Reset a Whirlpool Cabrio

1. Touch any key on the display pad to clear the error code, if applicable, or press "Pause/Cancel."
2. Choose a new cycle and press "Start" to begin.
3. Turn off and disconnect the Cabrio if the error or problem persists.
4. Wait several minutes before restoring power.
5. Contact Whirlpool for assistance if the unit will not reset.

How do I fix the l2 code on my Maytag dryer?

Replace the dryer fuse(s) or turn off the household circuit breaker for the dryer for one (1) minute, to reset the circuit breaker, then turn on the circuit breaker. Confirm that the power cord is properly installed. Refer the Installation Instructions for details. Select a Timed Dry heated cycle and restart the dryer.

How do I fix my Maytag dryer?

"AF" flashes if a restricted airflow condition exists. Check to make sure the lint screen is clean, the door seal is in place and the vent is not obstructed. Since you are certain that in your case this is not an issue then you may have a faulty sensor. You will need to replace the faulty sensor to fix this problem.

What does f40 mean?

The F40 error code indicates a communication failure between the main machine control board and the motor control board for the blower motor on the dryer. This can be caused by a loose wiring connection blown thermal fuse on the dryer, as well as a bad thermistor that is causing the dryer to overheat .

What does F mean on my washer?

The F indicates that the washer control detected a component problem. Since the door remained locked, your likely problem was with the drain pump or excessive suds preventing the washer from draining out the water properly.

What does check lint screen mean?

The control panel has an indicator light "Check Lint" or "Check Lint Screen" to remind you to clean the lint screen before each load. It is normal for the light to be on or flashing before the cycle starts. The indicator light will turn off once the door is opened or a cycle is started.

Where is the thermal fuse on a Kenmore Elite Oasis dryer?

On the Kenmore site for my unit it said look for the fuse on the dryer vent. On your dryer, the thermal fuse is located on the exhaust blower housing. To access the thermal fuse you will need to disassemble the dryer.

What does f2 mean on a dryer?

F2 flashes when there is a stuck button or user interface mismatch. You can try performing a hard reset to fix the problem. Unplug or turn the circuit breaker off for 30 seconds.

Why is my Kenmore Elite washer not draining?

If the washer won't drain there might be a clogged pump or hose. It's common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. Cleaned the filter and the machine still will not drain. So that must mean the hose or pump is clogged.

How do I reset my Kenmore Elite Smartwash quiet Pak 9?

How to Reset a Kenmore HE4t

1. Press and hold "Drain & Spin" for three seconds to release the child lock, if the keypad is locked.
2. Press "Pause/Cancel" twice to cancel the current operation.
3. Turn off and unplug the washing machine.
4. Wait several minutes before restoring power to properly reset the machine.