How do I turn off the turbo cool on my GE refrigerator?

TURBO COOL™ SETTING The fresh food temperature will revert to the coldest setting for an 8 hour period or until TurboCool is turned off (whichever comes first). It maximizes the cooling ability of the fresh food compartment. To turn the feature on or off, press and hold the Fridge pad for 3 seconds.

Beside this, how does Turbo Cool work on GE refrigerator?

TURBO COOL™ SETTING The TurboCool™ setting "revs up" the refrigerator, cooling it quickly after frequent or extended door openings and also when hot items are placed inside. When this feature is selected, the compressor is activated and the fans turn on at high speed. even when the door is open.

Secondly, what does Turbo freeze mean? The Turbo Freeze is a feature available on upright freezer model. When this feature is turned on, it will cause the freezer to cool to the lowest temperature and hold the temperature for 8 hours unless manually turned off.

Secondly, what does tC mean on GE refrigerator?

Turbo Cool

What is express chill?

Express Chill cranks the compressor into overdrive, chilling the inside of your freezer at a faster rate—perfect for when you're restocking or setting back up after a full clean.

What should my GE fridge and freezer be set at?

The temperature controls for the GE are set in the factory for 37 degrees Fahrenheit for the fridge and 0 degrees Fahrenheit for the freezer. You can change the refrigerator temperature within a range of 34 to 46 degrees Fahrenheit and the freezer temperature between -6 and 8 degrees Fahrenheit.

How do you reset a GE Profile refrigerator?

Press "1" and then "5" to completely reset the entire system. After the system resets, unplug the refrigerator and then restore power. The refrigerator is now reset.

Why is my GE refrigerator not cooling?

Evaporator Coil Frosting One of the most common causes of a GE refrigerator not cooling properly is a problem with the self-defrosting functions, according to the Appliance Repair It website. The parts likely to cause the problem are the defrost thermostat, defrost heater or the thermistor located above the coils.

What does EF mean on a GE refrigerator?

When set, you will typically see 'tF' in the temperature display when set to Turbo Freeze. Note: The symbol may look like an 'EF', an upside down f with an F, or something similar. This is not an error code, it is the Turbo Freeze (tF) setting.

Why does fridge say Sy EF?

Since SY EF indicates an evaporator fan circuit failure and you've already replaced the evaporator fan motor, check wiring between evaporator fan and control board.

How do you turn on a GE refrigerator?

To turn ON cooling system, press either REFRIGERATOR or FREEZER pad. The display will show the preset temperature settings of 37°F for refrigerator and 0° for freezer. To turn OFF cooling system, press and hold the REFRIGERATOR and FREEZER pads simultaneously for 3 seconds.

How do I reset my GE refrigerator motherboard?

How to Reset a GE Refrigerator

Pull your GE refrigerator out from the wall.
Find the electrical cord going into the wall's electrical outlet.
Plug your GE refrigerator back into the wall outlet and listen for it to start up again.
Open the freezer to the GE refrigerator and find the small shutoff switch on the icemaker.

How do you reset the temperature on a GE Profile refrigerator?

Then, use your fingers to press the four temperature setting buttons for 3 seconds. Afterward, you'll notice the number 0 flash in the electronic display. When this happens, press 1 and then 5 to completely reset your GE Profile Artica Refrigerator. Unplug the refrigerator for a few seconds and then plug it back.

What does dF mean on a fridge?

Frigidaire Refrigerator Error Code = dF. Condition = No defrost circuit.

How do I turn off Turbo Freeze?

TURBO FREEZE™ SETTINGS It maximizes the cooling ability of the freezer compartment. The TurboFreeze and TurboCool can be run at the same time. To turn the feature on or off, press and hold the Freezer pad for 3 seconds. On models with a touchscreen (LCD) display, press Express Mode.

What is GE turbo cool?

TURBO COOL™ SETTING The TurboCool™ setting "revs up" the refrigerator, cooling it quickly after frequent or extended door openings and also when hot items are placed inside. When this feature is selected, the compressor is activated and the fans turn on at high speed.